To use the matters needing attention in the process of - daily tools-Yangjiang Yangdong Ruitai Hardware Products Co., Ltd.

2020/03/10
The matters of attention in the use process: 1, we must pay attention to the protection in the process of using the blade, the blade is not suitable for cut, cut, are not suitable for see big bone for some big bone. Running a knife is to disconnect the raw material, the reasonable use of the blade, the cutting resistance, should be timely check the presence of bone residue, otherwise easy to hurt the blade. 2, often knife, sharp knife safer than a dull knife. Sharp knife cutting ingredients, need strength is small, more accurate is not easy to skid, the hand is not easy to tired. Placed 3, let the tool fully visible: knives, will put his hand on himself, and make sure the place after the tool will not accidentally fall, don't let towels, block holds off tool, otherwise prone to accident. Pass the knife is must pay attention not to point at others. 4, use the appropriate cutting tool: cut vegetables, meat, fish, cut bread, or do cold cuts, with a corresponding cutting tool; Cutting different ingredients, cut into different sizes, with different knife. 'There are specializing in' to develop various USES of cutting tools for a reason. 5, in the process of using props, especially as the tool is passed, it should be the handle towards each other, and the blade down, until after the other party take stabilizing the handle can be let go. Don't play with knives, so easy to produce risk. 6, when the cutter fall: knife falls, don't try to pick up by hand, it may be seriously injured. 7, placed in a safe place: sharp knives on children is very dangerous, must be put in the children's reach. 8, avoid contact with heat source: never knife on the kitchen or remove heat, or cutting tool is easy to damage or cause burns. 9, after use to pay attention to wash the knife with warm water, then put the water on a clean, especially material with cut too salty, because it has a garlic, time grew easily oxidized knife, the knife has a certain corrosive, cha in addition to not in time will affect the service life of cutting tools. 10, for the cutting tool long time need not, should be on both sides of the blade coated with grease, prevent rust, put in the process of the blade on a hard surface. 11, when after the operation, should be placed among the pier surface, no point, before after not c, and live, the blade should be block surface.
CONTACT US
Just tell us your requirements, we can do more than you can imagine.
Send your inquiry

Send your inquiry

Choose a different language
English
العربية
Deutsch
Español
français
italiano
日本語
한국어
Português
русский
简体中文
繁體中文
Afrikaans
አማርኛ
Azərbaycan
Беларуская
български
বাংলা
Bosanski
Català
Sugbuanon
Corsu
čeština
Cymraeg
dansk
Ελληνικά
Esperanto
Eesti
Euskara
فارسی
Suomi
Frysk
Gaeilgenah
Gàidhlig
Galego
ગુજરાતી
Hausa
Ōlelo Hawaiʻi
हिन्दी
Hmong
Hrvatski
Kreyòl ayisyen
Magyar
հայերեն
bahasa Indonesia
Igbo
Íslenska
עִברִית
Basa Jawa
ქართველი
Қазақ Тілі
ខ្មែរ
ಕನ್ನಡ
Kurdî (Kurmancî)
Кыргызча
Latin
Lëtzebuergesch
ລາວ
lietuvių
latviešu valoda‎
Malagasy
Maori
Македонски
മലയാളം
Монгол
मराठी
Bahasa Melayu
Maltese
ဗမာ
नेपाली
Nederlands
norsk
Chicheŵa
ਪੰਜਾਬੀ
Polski
پښتو
Română
سنڌي
සිංහල
Slovenčina
Slovenščina
Faasamoa
Shona
Af Soomaali
Shqip
Српски
Sesotho
Sundanese
svenska
Kiswahili
தமிழ்
తెలుగు
Точики
ภาษาไทย
Pilipino
Türkçe
Українська
اردو
O'zbek
Tiếng Việt
Xhosa
יידיש
èdè Yorùbá
Zulu
Current language:English